Momentum Modbus Plus 170 PNT Series Guide de l'utilisateur Page 137
- Page / 373
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Using the Modbus Plus Ports
870 USE 101 00 V.2.2
125
Cable Accessories for Modbus Plus Networks
Overview
This section describes the cables, connector and terminating device which should
be used in constructing a Modbus Plus network for TSX Momentum components.
Cable Within
Clusters
Cable for connecting two Modbus Plus devices within a cluster is available from
Schneider Automation in two lengths. These cables have a black boot.
Continued on next page
Description Part Number Photo
Modbus Plus or Modbus RS485
Short Interconnect Cable (10”)
170 MCI 020 10
Modbus Plus or Modbus RS485
3 ft. Interconnect Cable
170 MCI 020 36
- TSX Momentum 1
- M1 Processor Adapter and 1
- Option Adapter User Guide 1
- Document Set 4
- Contents 10
- About This Book 13
- Getting Started 15
- Overview of TSX Momentum M1 17
- Processor Adapters 17
- Section 1.1 18
- Front Panel Diagram 19
- Overview of Ports 20
- Power Supply 23
- Section 1.2 24
- 171 CCS 700 00 25
- 171 CCS 700 10 28
- 171 CCS 760 00 31
- 171 CCC 760 10 34
- 171 CCS 780 00 37
- 171 CCC 780 10 40
- Overview of TSX Momentum 43
- Option Adapters 43
- Section 2.1 44
- Section 2.2 45
- Serial Option Adapter 45
- Modbus Plus Option Adapter 51
- Section 2.3 51
- Section 2.4 57
- Assembling TSX Momentum 65
- Components 65
- Section 3.1 66
- Assembling a CPU 66
- Section 3.2 72
- Section 3.3 83
- Installation Guidelines 84
- Section 3.4 85
- Labeling the CPU 85
- Communication Ports 87
- Using the Modbus Ports 89
- Section 4.1 90
- Modbus Port 1 90
- Section 4.2 97
- Modbus Port 2 100
- Continued 100
- Continued on next page 101
- 870 USE 101 00 V.2.2 112
- RJ45 Pinout 113
- Overview 113
- Using the I/OBus Port 119
- How I/OBus Works 120
- I/OBus Accessories 123
- Using the Modbus Plus Ports 127
- Standard Cabling Schemes 131
- Cluster Mode Cabling Schemes 133
- Modbus Plus Addresses 144
- Peer Cop 146
- At a Glance 149
- Configuring an M1 CPU with 151
- Section 7.1 152
- Modicon Modsoft 153
- Section 7.2 169
- , Continued 173
- Setting the Time 174
- Reading the Time-of-Day Clock 177
- Section 7.3 178
- Changing Parity 183
- Changing the Baud Rate 184
- Changing the Modbus Address 185
- Changing the Delay 186
- Section 7.4 188
- Editing the I/OBus I/O Map 197
- Configuring a Modbus Plus 203
- Section 9.1 204
- The Default Peer Cop Screen 207
- Section 9.2 209
- Devices on the Network 210
- Continued 212
- On Error 214
- Section 9.3 227
- Completing the Configuration 248
- Saving to Flash in Modsoft 249
- Preparing to Save to Flash 250
- Saving to Flash 251
- Section 11.1 256
- Defaults for a 262
- 2.4K Machine 262
- Section 11.2 273
- Section 11.3 282
- Changing Mode and Data Bits 285
- Section 11.4 290
- Section 13.1 302
- Introduction 303
- Accessing the 303
- Section 13.2 308
- Section 13.3 319
- Using Peer Cop with Concept 330
- Saving to Flash with Concept 331
- Appendices 335
- Ladder Logic Elements and 337
- Instructions 337
- Ladder Logic 338
- DX Loadable Support 342
- A Special STAT Instruction 343
- Run LED Flash 349
- Pattern and Error 349
- TIO Power Supply Module 353
- Section C.1 354
- Module Overview 354
- Front Panel Components 355
- Specifications 357
- Section C.2 362
- Choosing a Terminal Connector 363
- Terminal Connector Coding 364
- ELECTRICAL HAZARD 365
- Numerics 369
HP AV8003 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Digitale Mediaplayer HP AV8003.
Wir stellen 1 PDF-Handbücher HP AV8003 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Commentaires sur ces manuels